V-Champ


I.D. Clamping End Prep Tool 95.25 mm I.D. to 355.6 mm O.D.



Bevels heavy wall tube, pulls a thick chip without cutting oils...

Built for Performance

Designed to prep all schedules of pipe from 3.75" I.D. to 14" O.D., the V-CHAMP features a state of the art I.D. clamping system that spreads the contact points of the clamps radially inside the pipe. This minimizes vibration for chatter-free end preps on both thin and heavy wall pipe. To assure stable, smooth rotation of the cutter head, this rugged tool employs opposed tapered roller bearings that are easy to adjust and never wear out.


  1. One mandrel and seven sets of clamps cover entire tool range
  2. Wide clamps spread the contact force for superior clamping
  3. Three powerful motor choices that are easily switched and inter changeable with the Rhino
    - Pneumatic
    - Electric
    - Hydraulic
  4. Dual opposed tapered roller bearing design provide years of trouble free service
  5. Available off-set gear drive lowers rpm, doubles the torque and enables the cutter blade to pull a thick chip for fast pipe beveling and increased cutter blade life.
  6. Heavy duty ratchet wrench and knurled knob allows easy clamping and is perfect for limited access areas
  7. Available spring hanger ensures accurate alignment when clamping
  8. Light weight and requires no special training
  9. Engineered for high performance and low maintenance
  10. Fully portable for on-site use

Precision pipe beveler makes chatter-free bevels for precision welds


Designed to bevel all schedules of pipe from 3.75” I.D. to 14” O.D., the V-Champ features a clamping system that spreads the contact points of the clamps radially inside the pipe. This minimizes vibration for chatter-free end preps on both thin and heavy wall pipe to assure stable, smooth rotation of the cutter head. This rugged tool employs dual opposed tapered roller bearings that are easy to adjust and never wear out.


Powerful and versatile, torque at the cutter blade for the V-Champ is achieved with the choice of three motor options suited to fit your application.


Like all Fabmax tools, the V-Champ is simple to operate and ruggedly designed for years of trouble free service.


Clamp System Features

Only 7 sets of clamps for entire range

All clamps work on one Mandrel

Clamp Pads have replaceable corners

All key clamping components, including Draw Rod are heat treated



Clamps spread force for rock solid stability


The V-Champ Jaws combined with Clamp Pads achieve a huge I.D. range of 95.25mm (3.75”) to 355.6mm (14”) with only 7 sets of clamps that all work on the same Mandrel. The Clamp Pads are V-shaped to spread the clamping force a daily inside the pipe for rock solid stability and have heat treated and hardened replaceable steel corners that are easy and economical to change when worn.


V-Champ Jaws Selector and corresponding spares Mandrel, Draw Rod, Actuator, Roll Pin, Retention Springs and Clamp Pad Corners



The V-Champ is equipped with two Tool Posts and a third Tool Post can be added as an option. All Tool Posts are inter change able and share the same screws and wedges.




Applications

  1. Super Alloy Pipe Beveling
  2. On and Off-shore Pipeline Construction
  3. Petrochemical
  4. Power Generation
  5. Systems Fabrication
  6. Structural Construction



The clamping system of the V-Champ pipe beveling machine has six contact points that minimize vibration for chatter free bevels on both thin and heavy wall pipe.


Super Duplex and other high alloy pipe materials can be difficult to bevel at speeds that work well on Carbon Steel and other alloys. The need to reduce the rpm and increase the torque is required for these applications and the Gear Box does just that. It easily and quickly mounts to the V-Champ and reduces the rpm by half and doubles the torque at the cutter blade.

V-Champ and Rhino motors are interchangeable and switching is easily accomplished with a simple hex key.


Working Range :
31.75mm I.D. to 114.3mm O.D. (Standard)
25.4mm I.D. to 114.3mm O.D. (with 1" Mandrel Kit)
19.1mm I.D. to 114.3mm O.D. (with 3/4" Mandrel Kit)


Motor Pneumatic Electric Hydraulic
Part No. 200011 200011E 200011H
3 hp (2237w) 120V AC 50/60 Hz 1800W, or 5 hp/8-12 gpm (30.3-45.4 lt/min)
90 psi (6.2 bar) 230V AC 50/60Hz 1800W 5-10 gpm @ 1500 psi
95 cfm (2690 lt/min) 20 gallon reservoir
Speed 24 rpm 13 rpm - 45 rpm 1 rpm - 22 rpm
Speed with Off-Set Gear Reducer 12 rpm with gear reducer 6.5 rpm - 22.5 rpm 1 rpm - 11 rpm
Minimum Clearance 323.9 mm 323.9 mm 323.9 mm
Head Length 660.4 mm 660.4 mm 660.4 mm
Working Weight 40.4 kg 41.3 kg 42.2 kg
Shipping Weight 91 kg 92 kg 93 kg
Shipping Dimensions 32” x 15” x 17”
813mm x 381mm x 432mm
32” x 15” x 17”
813mm x 381mm x 432mm
32” x 15” x 17”
813mm x 381mm x 432mm


Download Catalog


ENQUIRE NOW


Name





Email



Phone


Message



Congratulations. Your message has been sent successfully
Error, please retry. Your message has not been sent