Rhino


The work horse for beveling heavy wall pipe including super Duplex.
114.3mm I.D. to 457.2mm O.D. (4.5" I.D. to 18" O.D.)



Bevels heavy wall pipe and is easy to use offering an affordable alternative to specialized machines


Built for Performance

The RHINO features three drive choices that are capable of performing any degree of end prep on pipe up to 18" schedule 160 without cutting fluids. This portable tool has many advances including a self-centering draw rod actuated clamping system and wide clamps that produce a superior clamping force for chatter free end preps while assuring maximum blade life. Designed for years of trouble free service the proprietary gear and bearing system delivers the stability and performance that all FABMAX tools have become known for.

Built for boiler makers, there are no bushings to wear out and the sealed mandrel prevents debris from getting inside the tool, allowing it to be used in any orientation. What’s more the compact design requires a minimum of 67mm (2-5/8”) to fit between tubes.


  1. One mandrel and 8 set of clamps cover entire range
  2. Wide clamps spread the contact for superior clamping force and rigidity
  3. Three powerful motor choices that are easily switched and interchangeable with the V-Champ pneumatic, electric and hydraulic
  4. Available gear box lowers rpm and doubles the torque at the cutter blade
  5. The Fabmax cutter blade holding system hold the blades securely in place to produce a thick chip for fast pipe beveling and increased cutter blade life
  6. Bevels super alloyed pipe
  7. Patented Safety Spring hanger ensures accurate alignment when clamping
  8. Low maintenance dual opposed tapered roller bearing design provide years of trouble free service
  9. Efficient chatter-free cutter blade locking design directs heat away form tube surface and bevel blade cutting edge
  10. Fully portable for on-site use.

The Rhino performs any degree of bevel on pipe up to 18” schedule 160 without cutting fluid while assuring maximum cutter blade life. It has wide self-centering clamps that produce a superior clamping force for chatter-free bevels on all types of highly alloyed pipe.


Simple to operate and maintain, the Rhino features a choice of three motors pneumatic, electric and hydraulic. They can be easily switched with a simple hex wrench. The tool’s robust spur gear driver train and dual opposed bearing system are made of premium steels, heat treated, hardened & designed for trouble free service.


Clamp System Features


Only 8 sets of clamps for entire range
All clamps work on one Mandrel
Clamp Pads have replaceable corners
All key clamping components, including Draw Rod are heat treated and hardened.

Unrivaled Stability and Reliability


Fabmax innovative V shaped Jaws make six contact points with the pipe I.D. for unrivaled clamping stability and reliability. Heat treated and hardened steel Pad Corners are used on the Clamp Pads where they make contact with pipe I.D. for maximum durability. When they eventually wear out, they are easily and economically replaced.


Rhino Jaws Selector and corresponding spares Mandrel, Draw Rod, Actuator, Roll Pins, Retention Bands & Springs



Clamp set
Part No.
I.D. Range mm Mand.
P. No.
Size (in) Draw Rod Act. Roll Pin Retn.
Band/Spr.
D-01 114.3 142.9 D-37 4 D-15 D-12 D-13 D-14
D-02 139.7 168.3 D-37 4 D-15 D-12 D-13 D-14
D-03 165.1 193.7 D-37 4 D-15 D-12 D-13 D-14
D-02 & 04 190.5 219.1 D-37 4 D-15 D-12 D-13 D-14
D-03 & 04 215.9 244.5 D-37 4 D-15 D-12 D-13 D-14
D-02 & 05 241.3 269.9 D-37 4 D-15 D-12 D-13 D-14
D-03 & 05 266.7 295.3 D-37 4 D-15 D-12 D-13 D-14
D-02 & 06 292.1 320.7 D-37 4 D-15 D-12 D-13 D-14
D-03 & 06 317.5 346.1 D-37 4 D-15 D-12 D-13 D-14
D-02 & 06 & 07 342.9 371.5 D-37 4 D-15 D-12 D-13 D-14
D-03 & 06 & 07 368.3 369.9 D-37 4 D-15 D-12 D-13 D-14
D-02 & 08 393.7 422.3 D-37 4 D-15 D-12 D-13 D-14
D-03 & 08 419.1 447.7 D-37 4 D-15 D-12 D-13 D-14





The Rhino can bevel, face and bore heavy wall pipe at any
angle at the same time quickly and accurately for perfect
fit-up and precision welding.





Rhino II, 4.5” I.D to 24” O.D. Consult factory for availability





The Fabmax blade lock system and double threaded lock
screw hold the blade securely in place to produce a thick
chip that helps prolong blade life by transferring the heat
to the chip and away from the Cutter Blade.





152mm (6”) of polyethylene is removed from a steel pipe
O.D. and beveled for welding spool pieces together.



Working Range : 114.3mm I.D. to 457.2mm O.D.

Motor Pneumatic Electric Hydraulic
Part No. 200006 200003E 200003 Contour
932w 120V 8.5A 50/60 Hz 950W, or 932w
90 psi (6.2 bar) 220-240V 4.4A 50/60Hz 950W @ 1500 psi (102 bar)
95 cfm (2690 lt/min) 80 liter reservoir
Speed 15 rpm 13 rpm - 45 rpm 1 rpm - 14 rpm
Speed with Off-Set Gear Reducer 7.5 rpm with gear reducer 6.5 rpm - 22.5 rpm 1 rpm - 7 rpm
Minimum Clearance 374.7 mm 374.7 mm 374.7 mm
Head Length 711.2 mm 711.2 mm 711.2 mm
Working Weight 63.5 kg 64.9 kg 65.32 kg
Shipping Weight 131.6 kg 133 kg 133.4 kg
Shipping Dimensions 38” x 20” x 20”
965.2mm x 508mm x 508mm
38” x 20” x 20”
965.2mm x 508mm x 508mm
38” x 20” x 20”
965.2mm x 508mm x 508mm



Download Catalog


ENQUIRE NOW


Name





Email



Phone


Message



Congratulations. Your message has been sent successfully
Error, please retry. Your message has not been sent