Rhino 24


The work horse for beveling heavy wall pipe including super Duplex.
114.3 mm I.D. to 609.6 mm O.D.



Bevels heavy wall pipe and is easy to use offering an affordable alternative to specialized machines


Built for Performance

The RHINO 24 features three drive choices that are capable of performing any degree of end prep on pipe up to 18" schedule 160 without cutting fluids. This portable tool has many advances including a self-centering draw rod actuated clamping system and wide clamps that produce a superior clamping force for chatter free end preps while assuring maximum blade life. Designed for years of trouble free service the proprietary gear and bearing system delivers the stability and performance that all FABMAX tools have become known for.

Built for boiler makers, there are no bushings to wear out and the sealed mandrel prevents debris from getting inside the tool, allowing it to be used in any orientation. What’s more the compact design requires a minimum of 67mm (2-5/8”) to fit between tubes.


  1. One mandrel / wedge and 8 sets of clamps cover entire range
  2. Wide clamps spread the contact for superior clamping force and rigidity
  3. Three powerful motor choices that are easily switched and interchangeable with the V-Champ pneumatic, electric and hydraulic
  4. Available gear box lowers rpm and doubles the torque at the cutter blade
  5. The cutter blade holding system hold the blades securely in place to produce a thick chip for fast pipe beveling and increased cutter blade life
  6. Bevels super alloyed pipe
  7. Patented Safety Spring hanger ensures accurate alignment when clamping
  8. Sturdy, powder-coated stand for easy storage
  9. Low maintenance dual opposed tapered roller bearing design provide years of trouble free service
  10. Fully portable for on-site use.

The Rhino 24 performs any degree of bevel on pipe from 4.5" I.D. to 24” O.D. schedule 160 without cutting fluid while assuring maximum cutter blade life. It has wide self-centering clamps that produce a superior clamping force for chatter-free bevels on all types of highly alloyed pipe.


As an upgrade to the original Rhino, the Rhino 24 uses a wedge & actuator combined with an expanded cutter head to cover a range of 4.5" to 24" up to 2" thick wall. In addition to the enlarged cutting and clamping hardware, the Rhino24 kit comes with a special Safety Spring Hanger, a multi-position goose-neck hoist, & a powder-coated stand for easy maneuverability and storage


The tools are shown with the including special safety Spring Hanger and Lift Bracket. This innovative hanger provides a perceptible feel that the tool is aligned and centered to the pipe as the clamps tighten. The safety chain prevents the possibility of over extending the spring and provides a failsafe catch in the event of a spring failure.


The Gear Box reduces the rpm and doubles the torque at the Cutter Blade for beveling stainless steel and highly alloyed pipe when using the pneumatic or hydraulic motors and for all electric motor applications.


Kits come with a sturdy, powder-coated stand for easy storage and placement, while the Rhino 24 II is not in use.


Clamp System Features


Only 8 sets of clamps for entire range
All clamps work on one Mandrel
Clamp Pads have replaceable corners
All key clamping components, including Draw Rod are heat treated and hardened.

Unrivaled Stability and Reliability


Innovative V shaped Jaws make six contact points with the pipe I.D. for unrivaled clamping stability and reliability. All 8 sets of clamps work on both mandrel and wedge.


Heat treated and hardened steel Pad Corners are used on the Clamp Pads where they make contact with pipe I.D. for maximum durability. When they eventually wear out, they are easily and economically replaced.



Clamp set
Part No.
I.D. Range mm Mand.
P. No.
Size (in) Draw Rod Act. Roll Pin Retn.
Band/Spr.
D-1 266.7 311.4 D24-02 10 DII-06 DII-04 134-4616 D-14
D-2 285.8 330.2 D24-02 10 DII-06 DII-04 134-4616 D-14
D-3 310.9 355.6 D24-02 10 DII-06 DII-04 134-4616 D-14
D2 & D4 Pad 334.0 378.2 D24-02 10 DII-06 DII-04 134-4616 D-14
D3 & D4 Pad 363.5 403.4 D24-02 10 DII-06 DII-04 134-4616 D-14
D2 & D5 Pad 382.8 426.7 D24-02 10 DII-06 DII-04 134-4616 D-14
D3 & D5 Pad 407.7 451.6 D24-02 10 DII-06 DII-04 134-4616 D-14
D2 & D6 Pad 433.6 477.3 D24-02 10 DII-06 DII-04 134-4616 D-14
D3 & D6 Pad 458.2 502.2 D24-02 10 DII-06 DII-04 134-4616 D-14
D2 & D6 & D7 Pads 482.9 526.3 D24-02 10 DII-06 DII-04 134-4616 D-14
D3 & D6 & D7 Pads 507.5 550.9 D24-02 10 DII-06 DII-04 134-4616 D-14
D2 & D8 Pads 532.6 575.8 D24-02 10 DII-06 DII-04 134-4616 D-14
D3 & D8 Pads 557.0 600.2 D24-02 10 DII-06 DII-04 134-4616 D-14





Safety Spring Hanger and multi-position goose-neck Lift Bracket allow the tool to hang straight de-pending on tool configuration for easy mounting and release.





Compound bevel face, and bore on 24" carbon steal pipe, 2" wall & wall variance of 1/4"





Working Range : 114.3mm I.D. to 609.6mm O.D.

Motor Pneumatic Electric Hydraulic
Part No. 200024P 200024E 200024H
3 hp (2237w) 120V AC 50/60 Hz 1800W or 5 hp /8-12 (pump)
90 psi (6.2 bar) 230V AC 50/60Hz 1800W @ 1500 psi (102 bar)
95 cfm (2690 lt/min) 75 liter reservoir
Speed 15 rpm 13 rpm - 45 rpm 1 rpm - 14 rpm
Speed with Off-Set Gear Reducer 7.5 rpm with gear reducer 6.5 rpm - 22.5 rpm 1 rpm - 7 rpm
Tool Length (no stand) 762 mm 762 mm 762 mm
Max Working Weight 120.2 kg (265 lbs) 120.2 kg (267 lbs) 120.2 kg (268 lbs)
Shipping Weight 228.2 kg (503 lbs) 229.1 kg (505 lbs) 229.5 kg (506 lbs)
Shipping Dimensions 41” x 25.5” x 40”
1041.4 x 647.7 x 1016 mm
41” x 25.5” x 40”
1041.4 x 647.7 x 1016 mm
41” x 25.5” x 40”
1041.4 x 647.7 x 1016 mm



Download Catalog


ENQUIRE NOW


Name





Email



Phone


Message



Congratulations. Your message has been sent successfully
Error, please retry. Your message has not been sent